Hi
I have a Bruker Avance 400 MHz NMR system running with PC/XWINNMR
3.5pl6. I recently received this error message:
"tcuerror: error in line 0 (intrinsic) (pc=4, ld=8191): -FCU2 (rp=0,
wp=1712, stat=0x8040): ignored AQNEXT, busy FIF0 is stopped"
Since that, i cannot run any pulse program, or wobb. Always the same
error message.
I ran diagnosis application on the consol:
./aqxtest
System type is D*X
Necessary hardware (TCU, FCU, RCU) could be detected
Starting test for TCU at Mon Jun 4 17:21:45 GMT 2007
Output is saved in /tmp/prot.tcu
Please wait some minutes ...
TCU test: PASSED
Starting test for FCU at Mon Jun 4 17:23:15 GMT 2007
Output is saved in /tmp/prot.fcu
Please wait some minutes ...
FCU test: FAILURE
Error in FBUS interrupt test (fintr): interrupt 0: bit0 not set, rdstat=400
Error in FBUS interrupt test (fintr): interrupt 1: bit1 not set, rdstat=400
Error in FBUS interrupt test (fintr): interrupt 2: bit2 not set, rdstat=400
Error in FBUS interrupt test (fintr): interrupt 3: bit3 not set, rdstat=400
1 error found in 1 loop
Starting test for RCU at Mon Jun 4 17:24:27 GMT 2007
Output is saved in /tmp/prot.rcu
Please wait some minutes ...
RCU test: PASSED
Test for GCU is SKIPPED.
PASSED: TCU RCU
SKIPPED: GCU
FAILED: FCU
The content of the prot.fcu file is:
protocol has been opened.
FCU type 3
FCU 1 existing MEMORY CONFIGURATION 2 MByte at 16000000 to 161feffc
FCU 1 automatic detection: SLOT 2, LAYOUT 0, FCU VERSION 4
FCU 2 existing MEMORY CONFIGURATION 2 MByte at 16400000 to 165feffc
FCU 2 automatic detection: SLOT 2, LAYOUT 0, FCU VERSION 4
FCU 3 not existing
FCU 4 not existing
FCU 5 not existing
FCU 6 not existing
FCU 7 not existing
FCU 8 not existing
Running command 'auto' automatically ...
This test will take about 5 minutes...
FCU 1 existing MEMORY CONFIGURATION 2 MByte at 16000000 to 161feffc
FCU 1 automatic detection: SLOT 2, LAYOUT 0, FCU VERSION 4
Testing: instruction RAM by CCU (tim) ... PASSED
Testing: registers by CCU (tr) ... PASSED
load instruction RAM test (ldir) ...
load SGU RAM test (ldsr) ...
test FIFO RAM (fifo) ...
test VME-Quick-Pointer(0-31) (vqpoint) ...
test FIFO-Quick-Pointer(0-31) bits (fqpoint) ...
test FBUS interrupt BIT0-BIT3 in 'rdstat' register (fintr) ...
Error in FBUS interrupt test (fintr): interrupt 0: bit0 not set, rdstat=400
Error in FBUS interrupt test (fintr): interrupt 1: bit1 not set, rdstat=400
Error in FBUS interrupt test (fintr): interrupt 2: bit2 not set, rdstat=400
Error in FBUS interrupt test (fintr): interrupt 3: bit3 not set, rdstat=400
1 error found in 1 loop
Do you have any idea to solve my problem.
Thank you in advance
--
Serge Lavoie
Laboratoire LASEVE
Departement des Sciences Fondamentales
Universite du Quebec a Chicoutimi
555 boul. Universite
Chicoutimi, Quebec
G7H 2B1
Received on Mon Jun 04 2007 - 16:05:47 MST