Dear all,
there is a special 'Anleitung' to solve this problem:
ANLEITUNG REINIGUNG VERTIKAL ZYLINDER BACS H1259
Upwards motion failed Fehler 3 am display
oder Downwards motion failed Fehler 2 am display
1. BACS ausschalten
2. Zylinder zum Magazine per Hand schieben
3. Kolben nach unten drücken
4. Die 4 Imbuss Schrauben mit 4er Schlüssel entfernen
5. Kolben nach oben schieben
6. Unter dem 4 Quant Block den kontakt Ring mit Isopropanol reinigen
7. Die 2 Messing Halbschalen (oben am Kolben) mit Q-Tips und Isopropanol
reinigen und wenn nötig mit einem dünnen Schraubendreher den
Schmutz entfernen.
8. Den Kolben mit Isopropanol reinigen und dünnes Lager Fett (im Zubehör
Koffer des BACS H5042) auftragen
9. Kolben nach unten drücken und Block wieder in korrekte Position von oben
mit den Imbuss Schrauben anbringen (Richtung des Schlauchs!)
PS Beim Auftreten von Downwards Motion failed den Block von unten lösen
und reinigen
Viel Erfolg
Michel Neubert
How to clean the vertical cylinder of the BACS H1259
Upwards motion failed - error 3 at the display
Downwards motion failed - error 2 at the disply
1. switch BACS off
2. push to the magnet by hand
3. push the cylinder down
4. remove the four screws with the screw driver 4
5. push the cylinder up
6. under the black quant block - is a brass ring for contact - use Isopropanol
to get the old grease out
7. the two hafs of the brass half rings (on the top of the piston) - use Q-tips
and Iso-Propanol to get the complete dirt away - until the Q-tip keeps white.
8. Clean also the outer part of the piston with Isopropanol and put a small
layer of beige grease (H5042 in the box for the BACS) on the outside of the piston.
9. put the piston down and screw the screws in. If the piston does not go down -
please put the hose with the pressure in - off.
PS if the Downwards motion still failes - also remove the screws from the other
side and do the same cleaning on the bottom side of the black block.
Good luck
Michel Neubert
This is my translation for you.
I did this often with my 5 BACS systems and it helped often.
Good luck with the cleaning procedures.
Yours sincerely,
Ulrich Haunz
Am Donnerstag, September 26, 2024 00:11 CEST, schrieb "Heather Schenck"
> One more note on cleaning: to remove old grease, hexanes may be more effective than methanol.
-
=========================
Ulrich Haunz, Dipl.-Ing. (FH)
NMR-Spektroskopie
Raum L 710, L 807
NMR-Center M520, M521, M527
Postfach M 715
Fachbereich Chemie
Universitaet Konstanz
78457 Konstanz
Tel.: +49 (0)7531 88-4261 -> M521 Bruker Avance NEO 800
Tel.: +49 (0)7531 88-4422 -> L807 JEOL Lambda 400
Tel.: +49 (0)7531 88-4955 -> L710 Bruker AVIII HD 400
Tel.: +49 (0)7531 88-4956 -> M520a Bruker AVIII 600
Tel.: +49 (0)7531 88-4957 -> M527 Bruker AVIII 400 Automation
Tel.: +49 (0)7531 88-4958 -> M520 Bruker AVIII 400 WB
Tel.: +49 (0)170 9153213
FAX : +49 (0)7531 88-3898
=========================
-=-=-=-=-=-=-=-=-=-=-=-
Groups.io Links: You receive all messages sent to this group.
View/Reply Online (#1645): https://urldefense.com/v3/__https://ammrl.groups=
.io/g/main/message/1645__;!!PvDODwlR4mBZyAb0!VyxKn18cQ-ep6OtxMLN_1U1y6dXQZR=
9LauyVtrYJFynLLQRUxxM7fZTxnwtpJGBjxb5NxmvnQmIutAKMkhTtq2NyuPHFsA$
Mute This Topic: https://urldefense.com/v3/__https://groups.io/mt/108655772=
/7559972__;!!PvDODwlR4mBZyAb0!VyxKn18cQ-ep6OtxMLN_1U1y6dXQZR9LauyVtrYJFynLL=
QRUxxM7fZTxnwtpJGBjxb5NxmvnQmIutAKMkhTtq2NVLLKXig$
Group Owner: main+owner_at_ammrl.groups.io
-=-=-=-=-=-=-=-=-=-=-=-
Received on Thu Sep 26 2024 - 00:53:37 MST